GE Ethernet Wall Plate Wiring Diagram

  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  
  •  

Wiring a GE ethernet wall plate can be a very confusing and tedious task, but with the right directions and hints you will be able to install the network wall plates in a jiffy.  Before we start wiring the Cat5 network wall plates, let me tell you a story.  I recently installed a couple of GE ethernet wall plates with the coaxial connection for cable or satellite tv in my apartment, to bridge the gap between the walls between my two rooms.

After looking at the directions that GE provided to install the GE ethernet wall plate.  I realized that they were really confusing, uninformative and plainly just piss poor directions. So I decided to write this how to guide on install GE ethernet cable wall plate to make your job easier.  This should also work for other network wall plate brands, just make sure that you match up the correct cable color with the right pin number.

GE Ethernet Wall Plate Wiring

GE Ethernet Wall Plate Wiring

To begin the installation of the cat5 network wall plates, you will first need to strip off about 2 inches of the plastic shield to expose the eight color wires inside.  Next you will then need strip off about 3/8 to 1/2 inch of the dielectric material to expose the copper conductor.

Remember to only strip off enough of the dielectric material that you will need to work with because if you expose too much copper conductor this could create crosstalk in the cable.  After you have stripped the cat5 cable to the proper length, will then need to use the following chart to wire a straight-though cable connection to the GE ethernet and coaxial wall plate.

GE Ethernet Wall Plate Cable Wiring

GE Ethernet Wall Plate Cat5 Ethernet Cable
1 Blue
2 Orange
3 Black
4 Red
5 Green
6 Yellow
7 Brown
8 White
White / Orange
Orange
White / Green
Blue
White / Blue
Green
White / Brown
Brown

GE Ethernet Wall Plate – Yahoo Answers.

Structured Data, Review
Title: GE Ethernet Wall Plate Wiring Diagram
Reviewed by Dustin Macheske on Dec 7
Rating: 5.0
Summary: Ge ethernet wall plate wiring diagram. Learn how to install and wire a GE cat5 ethernet wall plate for your home network.
Description: Ge ethernet wall plate wiring diagram. Learn how to install and wire a GE cat5 ethernet wall plate for your home network.

116 Responses to GE Ethernet Wall Plate Wiring Diagram

  • brian says:

    this was exactly what i needed to wire my house for internet thank you

  • Steve Blake says:

    Perfect!. GE sells this plate at Home Depot but can’t tell you how to wire it. Bingo. You nailed it.. Thanks

  • Eddie says:

    why couldn’t they have done that ? Thanks for the help ! works great now …

  • Paige says:

    machesked…you are a sweetheart!!! I can fix the entire house now..the electrician couldn’t even do this!! But now I can. Thanks so much!!

  • Brad says:

    Thanks. I appreciate someone making some sense.

  • John says:

    I agree with the other messages. Thanks for helping. I was surprised there was not any direction sheet in the package. They should print this site and include it in the future packages!

  • star says:

    why couldn’t GE package designers be as GENIUS as you? I mean, I’m really glad they let me know where to put the screws, because that was SOO tricky.

    THANK YOU!

  • Smer says:

    THANK YOU! I have done networking for the last 10 years and I have never seen the colors they provided on the back of their connector.I wired it as if I were doing a normal straight through. I must still have a kink somewhere because according to your chart I did it correctly, but I needed to find some reference since GE did not include any – this bit of instruction was MUCH NEEDED! Thanks again,

  • Kathy says:

    Thank you so much! This help a lot!

  • Kym says:

    Perfect!!! Saved us a lot of time!

  • Ray says:

    Thanks a million! Makes you wonder how it got packaged without instructions. I have one question. I am running cat 5E to the opposite side of the house (lets call this wallplate 2). Wallplate 1 will be near my router. I want to make things look neat by coming from my router with a patch cord to wall plate 1. My question is, will my wiring be just the opposite on one end or will both be the same? Thanks

    • machesked says:

      The wiring will be the same on both wall plates. If you hooked it up opposite on the other end, you would have a cross over connection.

  • Ross says:

    I have fought with this for a few hours tonight and just found this site. I have 6 wires in my ethernet cable and am using 2 of them (blue and blue/white) for phone. I want to use the other 4 (orange, orange/white, green, green/white) for my network. I have this set up on another jack in the house but I did not install it and I can’t get to it as it is buried behind the TV wall unit. I followed the instructions above but am still not working. Is a 4 wire set up different than the 8 wire above? Can anyone help?

    Thanks in advance.

    • machesked says:

      As far as I know, you need all eight cables in the ethernet cable just for the network. A few of the cables are for transmitting and receiving data. Others will be used for power and grounding.

  • Lou V says:

    Thanks this help a lot. And got me out of trouble on a job site.

  • Joe says:

    If I shut off “airport” on my wife’s Apple Mac Book and plug in the Ethernet cable from the wireless router to the laptop, I get an internet connection. When I plug the cable back into the GE wall plate (the wiring is exactly as you have listed, on both ends), and plug in an Ethernet cable from the wall plate to the laptop I cannot get an internet connection. Any idea what could be wrong? I even changed out the wall plates in two different rooms in case they were the problem. Can I run the Cat6 cable from wall plate to wall plate?
    Thanks for any help you can give me.

    • machesked says:

      You can run cat6 cable to connect the two wall plates together. Make sure that when you connect each cable to the wall plate, that the exposed copper cable is only connected to the right connector and is not touch any other connector. This could short out the connection.

  • Al C says:

    THANK YOU! That was perfect! GE’s instruction was not user friendly. They assumed people are tech savvy. Thanks again.

  • Rick says:

    I have cable internet and only one jack in my bedroom and the modem is connected to that jack. My question is..How can I get cable TV in my room when the only jack is being used by the modem? Tried an splitter but the internet goes down. Please advice.

    • machesked says:

      The problem you are having is that the cable signal is being split too many times causing a weak signal for your cable modem. The way to run cable tv and cable internet is to place a two way splitter at the main feed. The main feed is where the cable company ran a cable from the electrical pole to your house. Once you install the two way splitter run one cable from the output to your modem, then run another cable from the other output to your tv. If you have to run multiple tv’s then you can hook another splitter to to the two way splitter. If you are only running one tv and one modem in the same room, find the splitter that the cable company installed and barrel the lines together, then move the two way splitter into that room. You could also be using the wrong type of cable or a splitter that doesn’t hold the right frequencies for you cable internet service. Make sure that you are using RG-6 coaxial cable and a splitter that hold 2150MHz.

  • Klaus says:

    Hey thank you so much for this information, Internet works fine now in all rooms thanks to this advice :-) We will never understand why GE doesnt use the same color code then in the Network Cables, so dont waste you time time thinking about that, just do the wiring like its listed here ;-)

  • Traitimmapu says:

    I have GE Network WallPlate connected to one end of the CAT5 and wired the same as the above screen shot. However, what i would like to know is how to wire the other end of the cable using the RJ45 jack (male) so that i can connect it to a Router?

    I tried to wire the RJ35 jack male as follow:

    White/Orange
    Orange
    White/Green
    Blue,
    White/Blue
    Green
    White/Brown
    Brown

    However it doesn’t seem to work. Can you please give me some ideas how to wire it on the male end?

    thanks in advance

    Traitimmapu

    • machesked says:

      This wrote this article to show how to wire two ethernet wall plates together, plus I forgot that not all people use switches in their house. You might need a cross over cable to connect your pc to your router, you could either rewire the ethernet wall plate, or the connector.

      1. White/green
      2. green
      3. white/orange
      4. blue
      5. white/blue
      6. orange
      7. white/brown
      8. brown

      • mjs says:

        Thanks, machesked – the set of crossover wiring instructions was exactly what I needed. The GE wall plate did the trick, but only after I located your insight! For anyone else interested: I needed to run a wired ethernet adapter from my tivo to the back of a GE wall plate. One end of the cat5e is an RJ45 (plugged into the linksys adapter) and the other to the wall plate. Using the crossover version of the diagram – I was able to make the connection.

        • Dennis says:

          I have a GE wall plate on one end and a Leviton RJ45 receptacle on the other end. Should I use the T568 A or B wire pattern on the RJ45? Which color pattern should I use on the GE wall plate? Thanks!

    • Gonzalo Vidal says:

      It is very interesting am amazing about this web believe me I spend like 45 minutes to try to know about the ge network wall plate installation and thanks Gad that you provide this information for every one thanks

  • Traitimmapu says:

    Thanks Machesked for the update.

    I’m still confused. If I’m using Ethernet CAT5 cable to connect from the Wall plate to my computer. I would wire the wall plate as the same as the above. But for the other end of the Wall Plate wire I would wire as you mentioned below to connect this end to the router correct?
    1. White/green
    2. green
    3. white/orange
    4. blue
    5. white/blue
    6. orange
    7. white/brown
    8. brown

    Thanks
    Traitimmapu

    • machesked says:

      Yep. By wiring one end according to the original document and then the other end according to what I wrote yesterday, you will create a cross over cable.

  • Traitimmapu says:

    Thanks machesked!

    I will try it out and let you know if it works or not.

  • Traitimmapu says:

    Hi Machesked,

    I tried the wiring you sugguested and i’m not getting connection.

    Thanks

  • Ray says:

    Thank you for writing this guide. I just purchased these wall plates and found the directions as you put it “piss poor” also. You saved the day for me and eliminated a lot of trouble shooting for me I am sure. Thanks again!

  • Jeff says:

    Thank You! Thank You! Thank You!

  • Allen says:

    Thank you so much for your help. Can’t believe they didn’t put instructions in the package. Swore we had the wrong product because of it!

  • Ronnie says:

    Hey, I bought one of those GE wall plate and was having trouble for a day and a half with no connection. The package simply said to connect the wires according to the color coded wires, well…that didn’t work…I came across your wire chart for what wires go where, tried it, and lo and behold…IT WORKS..! I now have blazing fast speed on my xbox 360…!

    Thanks for posting your wire chart. It was a big help…!!!

  • KMae says:

    Thanks a million! GE ought to be paying you!

  • collin says:

    would this be the same if i use a cat6 instead of cat5e?

  • acutturi says:

    I just bought a house that was supposed to be wired for Ethernet, but each wall outlet has a coax cable connection and a phone connection. I questioned the builder who argued that it is cat5 cable going to the phone connection and if I want cat5 outlet I have to rewire the faceplates, so I bought these GE faceplates and found this site (thank you 1000x over for this site!), but now when I take the faceplates off the wall I have 2 sets of cat5 wires for a total of 8 white wires with no color stripes. 2 sets(4 wires) were joined together, leaving 2 sets unpaired.
    Any suggestions on how to complete the wiring? It is Christmas day and I am trying to get my son internet in his room above the garage that gets crappy wireless reception and has 2 of these (supposed) cat 5 outlets installed in the wall.
    Any help is appreciated!

    • acutturi says:

      I think I understand it now a little better after looking at the wires further up the wall. The white wires aren’t actually stripped, they are just twisted with another color, so if I look further up into the wall I can see where each white wire comes wrapped around a specific color, then I just refer to the chart to connect it, right? I hope I solved my own dilemma…

  • bartels says:

    awesome – the package did suck, no directions at all -

    You rock

  • Brian says:

    I need to go from my modem to the wall plate, then the wall plate into my router in the attic, where I will split the wired signal between two more wall plates. I am completely lost, but I have the crimpers, connectors, and wall plates. HELP!!!!

    • machesked says:

      Just wire one room at a time. So wire the wall plate where your modem, then wire the wall plate in the attic that will connect to your router. Take a laptop up there and make sure you are getting internet. Then your should be able to run ethernet cables from your router and connect to the other walls that go to the other rooms in your house. All the wall plates will be wired according to the diagram.

      • Brian says:

        Sounds great, so how do I wire the ethernet connectors? I tried “A” but it did not seem to work. I already tried the laptop in the attic. The router in the attic is wireless, but I will run wired connnections out of it.

        • machesked says:

          You need to use 568-B standard on both ends.

          Pin 1 = White/Orange
          Pin 2 = Orange White
          Pin 3 = White/Green
          Pin 4 = Blue/White
          Pin 5 = White/Blue
          Pin 6 = Green/White
          Pin 7 = White/Brown
          Pin 8 = Brown/White

          • Brian says:

            Excellent. 3 wall plates wired as you say above, and 3 connectors in the attic wired with the “B”. One is input (from one wall plate to the attic), the other two go out to the 2 remaining wall plates. Thanks!

          • machesked says:

            No problem just remember if you ever trying connecting a ethernet switch to another switch you will need to make a cross over cable to connect them.

  • Brian says:

    Going from cable modem out to wall plate (store bought ethernet cable). Then from that plate into the wireless router in the attic. From the router I am going to run two out back to wall plates. So I am just wiring 3 wall plates and 3 connectors in the attic. Starting now, will let you how it goes. Can’t thank you enough for the help.

  • TJS says:

    Thank you so much for this outstanding contribution and fix. Can’t believe GE wouldn’t include your chart with their packaging. Many, many thanks!!!

  • mikeo says:

    On the wire that I got from where I work, I found that none of the wire colors corresponded to the colors in the wall jack. I took one end of the wire(cat 5 plug still attached)plugged it into the GE jack. I cut the other end off and stripped back the wires. I then took an ohm meter(from the cut end to the screws in the jack) and matched up each of the cable wires to which screw in the jack they were connected to and recorded this info on a sheet of paper. Apparently the manufacturer is too ignorant to tell you that there are many different wires out there and it is very simple to match them up.

    • machesked says:

      It would be nice if they showed a diagram, im guessing since there are so many standards they don’t bother. Probably cost one more cent in manufacturing. : )

  • marty says:

    Thanks,This info was excactly what I needed.Shame on G.E. for not including this in their packaging.

  • Mike says:

    I have connected the wall plate per your color guide. Thank you. I now need to connect the other side to mine 8 port switch. Which color scheme do I use on the switch side? Thanks again.

    Mike

  • AJ says:

    Saved me the time from having to chart this out myself. Thanks!

  • Michael says:

    I read in one of your comments that one of the wires is used as a ground. Does this mean that that wire terminal does ‘not’ run through the Cat-5 but simply stops at the wall? The Cat-5 is just copper wires that carries a signal from one end to the other…right? Why can you not just use any wire combination on any terminal as long as they are wired on the same terminals for both wall plates?

    • machesked says:

      You can use any combination that you want as long as they are the same on both ends, it is about standardization.

      • Absolver says:

        Even if it is the same on both ends, it won’t work unless you custom make your own cables to connect to things in the outside world.

  • Kotti says:

    Excellent doc….worked sweet.

  • Teresa says:

    Thank you very much! Very helpful.

  • Jamie says:

    I couldn’t believe that this wall plate didn’t use standard wire colors. Thank-you for providing this!

  • Bob says:

    I’m quite surprised that this wall plate is marketed for cat6, let alone cat5e. I saw this thing at Home Depot recently and just about fell over!! As a professional network technician with many years of commercial, industrial ,and has working knowledge everything from EIA TIA specs all the way to complex routing protocols, these jacks WOULD NEVER pass a cat6 let alone a cat5e cable test. When cat 5e cables are terminated you are only allowed maybe 1/4″ of pairs being untwisted, even less for cat6 It is VERY IMPORTANT to maintain the pair twist right up to the point of termination. I have installed thousands of cat5 and cat6 terminations as well as many miles of cable and based on what I saw at the store(and this website) there is far more than 1/4″ of untwisted pairs, also wires from different pairs are running against each other not maintaining any type of proper twist. This jack would certainly fail a cross talk test as specified under EIA TIA standards. As a professional I would never use these!! The Leviton keystone quick ports are a much better alternative and cost wise not much different. Anyway my .02..

  • Joe says:

    Thanks a lot. Would not have figured this out without your guide; was totally easy with it!!

  • Julie says:

    Thank you so much. This was a huge help. I’m so glad we found this. We had to do the crossover connection and the instructions worked perfectly.

  • Dom says:

    Hi there..how do you know whether the wiring on an RJ45 connector is straight through or cross over?

    • machesked says:

      A straight through and cross over are two ways you can wire a rj45 connector
      More then likely you will need to wire a straight through connection. You would wire a crossover connection forlike devices, for instance switch to switch or pc to pc.

  • Will says:

    Thanks, worked like a charm. Per a previous post, shame on GE for neither using the right colors nor bothering to explain it.

  • Rav says:

    I need help using the same cat 5 cable for both Phone and ethernet. My blue and white and orange and wihite are being used for phone line. Can I use the other 4 wires ( Brown, Greeen abd theirrespective stripes for ethernet using the GE wall plate.

    Thanks in advance.
    I could not have said it better than everyone before. GE should pay you for making their equipment work.

  • Dan says:

    That jack didn’t work for me, in fact it cost me a lot of time and grief. I re-bought using Leviton the 2nd time and all my problems vanished. The GE is a nice looking connection but there is no directions and the color-coding makes no sense. Leviton, while not as nice looking, had complete wiring directions and a much simpler wiring connection.

  • Tyler says:

    Wow, thanks!

  • alex says:

    This was an excellent how to guide. I was racking my brain for days over this stupid jack system. I reset my network thinking it was that, and it wasn’t. It’s the bean pushers at GE, thinking that network installers wouldn’t need the normal Cat5 coloring. Thanks so much.

  • Bobby says:

    Your a genius! Along with everyone else who looked at this site I have been really confused about how to go about wiring this face plate. Thank you very much!

  • John says:

    Thank you sooooo much!

  • Len says:

    Thank you soooooo much !!! It’s amazing that they, “GE”, could not have done that. My wire and wall plate connections work fantastic now.

  • Jeff Althaus says:

    This is exactly what I needed and it worked like a charm! Thank you!

  • Tom says:

    Does anyone have the proper color combination for telephone? I bought a version with joint Ethernet and telephone. The network side is working fine after installing as described above, but telephone is not working based on the colors to standard color pin out.

  • Ajit says:

    Thank you… Thank you… for saving my life tonight… it was fun connecting and seeing it work first time…

  • Karthik says:

    Thank you… thank you.. I cannot thank you enough.. you saved me atleast 1 hour and a lot of mental stress.. keep up the good work

  • Tony says:

    I am wiring Cat5e patch cable to the back of the GE wall plate. I am running that wire through the ceiling to another wall plate so I dont have to have a ethernet cable running across my floor. Do I use the diagram above for both wall plates or do I have to switch it up or can I have my modem at the one wall plate and my router at the other so I can plug in my xbox with a shorter cable. Any help would be greatly appreciated. Thanks

  • Tony says:

    After wiring the wall plates the same. Do I plug the modem and router on one wall plate and run an ethernet cable to what ever device I want to use or do I run the modem on one wall plate and the router on the other wall plate?

    • machesked says:

      It depends on what you are trying to do. The modem will plug into the router. If you have more devices where the Xbox is located then put the router next to Xbox.

  • Tony says:

    one last question. So if I have the modem on wall plate and the router on the other wall plate,
    I still wire the two different wall plates the same way as you showed above?

  • Eugene says:

    Thanks a million for getting this info. IT is very very helpful. Saved me a trip.

    This is 2012 and now I am wondering why GE doesn’t have their acts together about following the standard. After they’ve received tax payers money to help with their bailout all they have to give back is sub/non-standard products.

    I was shocked when I read their instructions. They need to do better; hire the right people to get the job done. Don’t they know about CAT5/6 cable color coding?

  • Mehdi says:

    Thank you!

  • Trevor says:

    Thank you for this! How dumb for them to use non network color coding to wire up a Cat5/5e/6 cable, or to provide color to color matches.

  • Pingback: Cat 5 wiring | Partagé des expérience aléatoire

  • Javier Baldiviezo says:

    Thank you!! I was going nuts with the wiring

  • Pattertwig says:

    I used your wiring diagram for a CE-E-Tech Ethernet wall plate. It didn’t work the first time, but when I disassembled it, I noticed that one of the wires had broken when I tightened down the screw. I redid the wires in the same order and it works great! Thank you.

  • Patsy Herring says:

    i have water damage in my loft and a 12″ section of joist and 12″ section of wall plate need repairing. i want to know what i need to do to get the job done properly. i have read that i could bolt a new joist to the existing one but what kind of bolts would i need. sorry but i am a complete novice at this kind of thing. thanks for all your answers.

  • Kelli Shanklin says:

    What’s the best way to install a telephone wall plate? I know that I can run the phone line through the wall but should the wall plate simply be screwed into the drywall or should I buy a base (such as the kind that are used for light switches) to attach it to? It’s a standard wall plate with two screws. Thank you.

  • Cecilia Osburn says:

    What’s the best way to install a telephone wall plate? I know that I can run the phone line through the wall but should the wall plate simply be screwed into the drywall or should I buy a base (such as the kind that are used for light switches) to attach it to? It’s a standard wall plate with two screws. Thank you.

  • Dollie Mccrystal says:

    How do I install an HDMI wall plate for a connection directly into the wall? What is the benefit of this versus just having an HDMI cable into a regular wall outlet? Are all HDMI cables created equal? Will I only need one HDMI cable for a dvd, tivo, and cable box?

  • Marcia Hester says:

    I have wall mounted my 40″ Samsung LCD in my room, and because I am a perfectionist, I got a power point and a HDMI wall plate installed behind the TV to hide cables. But after it is all set up when I use my PS3 or my PC on the TV through the HDMI cable that I have running through the wall, I am getting pixelation. It is like a lot of dead pixels, but they are always in different spots, so it is more like dead colours. The pixels usually stick to lines of what I’m watching, for example I might watch a movie, and there are dead pixels around a cloud, but when the cloud moves, the pixels follow it. I think the problem might be dues to long length of cables, and multiple joins in the cables. From my PC I have a 1 meter HDMI cable going to the wall plate, which then goes to a 7 meter HDMI cable which goes to the other wall plate which goes to a right angle adapter which goes to another 1 meter cable which goes to another right angle adapter which finally plugs into the TV. Is it a possibility that the long length and lots of connections it is loosing continuity?

  • Noemi Madero says:

    Im planning to connect my speaker to my receiver in wall. But first i want the speaker wire to be (from my receiver to connect to wall plate). I dont know how to connect my wire(from wall plate to in wall speaker). I’m guessin this is the sequence(tell me if i’m right or wrong).

    Receiver—>Speaker wire—>wall plate—>Another speaker wire?(my main question)—>Speaker

  • Melissa Nason says:

    Okay, so we have a gable roof. We want to extend a cable internet cable from our garage to where our TV is in the lounge (next room). It’s obviously fine to get up into the roof, but I am curious as to what happens when the cable gets to the wall that the TV backs onto. Is there some sort of cavity that goes down from the roof in the wall behind the TV? It is a “standard” wall I think with wood stud and gyprock/plaster sheet on either side.

    I’m imagining that it looks kind of like this on the side – —–┐┌—– but I understand that there are also horizontal bars (noggins I think?) which might be half way down the wall so I don’t know really.

    I am looking at getting PayTV in a rental and they will allow wallplates to be installed but not much else.

    Thanks!
    Hey, thanks. The TV is not on the same wall as the garage. The TV is on the opposite side of the living room to the garage. There is definitely a cavity in the wall but I wasn’t sure if it was just open at the top. There is no insulation. I know there is a cavity because the same wall the TV next to is also shared by the front door, and the door handle knocked a hole in the gyprock once and it was empty space.

  • Elinor Sturgell says:

    Could anyone tell me how to wire a CAT6 Ethernet cable into a wall plate?

  • Alejandra Fleishman says:

    Hello,

    I am purchasing a house and want to drop wires for surround sound. My question is, is it best to just have the wire come out of the wall and then mount the speaker right there or should I buy wall plates with speaker connections/banana binding? Never done this before and want to know “best practices”. At first I was thinking wall plates but now that I’m looking into it, you are going to still see wires coming from the plates so what is the point?

    thanks!

  • Sonia Gourley says:

    Hello,

    I am purchasing a house and want to drop wires for surround sound. My question is, is it best to just have the wire come out of the wall and then mount the speaker right there or should I buy wall plates with speaker connections/banana binding? Never done this before and want to know “best practices”. At first I was thinking wall plates but now that I’m looking into it, you are going to still see wires coming from the plates so what is the point?

    thanks!

  • Stella Sotelo says:

    I have wall mounted my 40″ Samsung LCD in my room, and because I am a perfectionist, I got a power point and a HDMI wall plate installed behind the TV to hide cables. But after it is all set up when I use my PS3 or my PC on the TV through the HDMI cable that I have running through the wall, I am getting pixelation. It is like a lot of dead pixels, but they are always in different spots, so it is more like dead colours. The pixels usually stick to lines of what I’m watching, for example I might watch a movie, and there are dead pixels around a cloud, but when the cloud moves, the pixels follow it. I think the problem might be dues to long length of cables, and multiple joins in the cables. From my PC I have a 1 meter HDMI cable going to the wall plate, which then goes to a 7 meter HDMI cable which goes to the other wall plate which goes to a right angle adapter which goes to another 1 meter cable which goes to another right angle adapter which finally plugs into the TV. Is it a possibility that the long length and lots of connections it is loosing continuity?

  • Patsy Herring says:

    Hello,

    I am purchasing a house and want to drop wires for surround sound. My question is, is it best to just have the wire come out of the wall and then mount the speaker right there or should I buy wall plates with speaker connections/banana binding? Never done this before and want to know “best practices”. At first I was thinking wall plates but now that I’m looking into it, you are going to still see wires coming from the plates so what is the point?

    thanks!

  • Desmarais says:

    What’s the best way to install a telephone wall plate? I know that I can run the phone line through the wall but should the wall plate simply be screwed into the drywall or should I buy a base (such as the kind that are used for light switches) to attach it to? It’s a standard wall plate with two screws. Thank you.

  • Anne Felton says:

    I recently bought a house and I’m changing the receptacles around the house and some dummy stripped the screws in the wall plates. What bit do I need to get those things out?

  • Monique Spalding says:

    Okay, so we have a gable roof. We want to extend a cable internet cable from our garage to where our TV is in the lounge (next room). It’s obviously fine to get up into the roof, but I am curious as to what happens when the cable gets to the wall that the TV backs onto. Is there some sort of cavity that goes down from the roof in the wall behind the TV? It is a “standard” wall I think with wood stud and gyprock/plaster sheet on either side.

    I’m imagining that it looks kind of like this on the side – —–┐┌—– but I understand that there are also horizontal bars (noggins I think?) which might be half way down the wall so I don’t know really.

    I am looking at getting PayTV in a rental and they will allow wallplates to be installed but not much else.

    Thanks!
    Hey, thanks. The TV is not on the same wall as the garage. The TV is on the opposite side of the living room to the garage. There is definitely a cavity in the wall but I wasn’t sure if it was just open at the top. There is no insulation. I know there is a cavity because the same wall the TV next to is also shared by the front door, and the door handle knocked a hole in the gyprock once and it was empty space.

  • Christy says:

    I have inherited a set of china wall plates. It may not be the cool thing to place upon the wall and perhaps most would send the set to a charity shop but I really do like them and wish to see them upon my wall. Have been told not to use the metal coated with plastic type to hang the plates as they may damage the plates. Am definitely a DDIY but believe I’m capable of banging a nail into a wall.
    Any suggestions please what to use as the plates don’t have a hole through them. Or are the metal coated type OK.
    Thank You.

  • Alejandra Fleishman says:

    What’s the best way to install a telephone wall plate? I know that I can run the phone line through the wall but should the wall plate simply be screwed into the drywall or should I buy a base (such as the kind that are used for light switches) to attach it to? It’s a standard wall plate with two screws. Thank you.

  • Patty Guest says:

    I recently bought a house and I’m changing the receptacles around the house and some dummy stripped the screws in the wall plates. What bit do I need to get those things out?

  • Christy says:

    Im planning to connect my speaker to my receiver in wall. But first i want the speaker wire to be (from my receiver to connect to wall plate). I dont know how to connect my wire(from wall plate to in wall speaker). I’m guessin this is the sequence(tell me if i’m right or wrong).

    Receiver—>Speaker wire—>wall plate—>Another speaker wire?(my main question)—>Speaker

  • Christy says:

    I recently bought a house and I’m changing the receptacles around the house and some dummy stripped the screws in the wall plates. What bit do I need to get those things out?

  • Marcia Hester says:

    I have wall mounted my 40″ Samsung LCD in my room, and because I am a perfectionist, I got a power point and a HDMI wall plate installed behind the TV to hide cables. But after it is all set up when I use my PS3 or my PC on the TV through the HDMI cable that I have running through the wall, I am getting pixelation. It is like a lot of dead pixels, but they are always in different spots, so it is more like dead colours. The pixels usually stick to lines of what I’m watching, for example I might watch a movie, and there are dead pixels around a cloud, but when the cloud moves, the pixels follow it. I think the problem might be dues to long length of cables, and multiple joins in the cables. From my PC I have a 1 meter HDMI cable going to the wall plate, which then goes to a 7 meter HDMI cable which goes to the other wall plate which goes to a right angle adapter which goes to another 1 meter cable which goes to another right angle adapter which finally plugs into the TV. Is it a possibility that the long length and lots of connections it is loosing continuity?

  • Lorrie Lauro says:

    I have wall mounted my 40″ Samsung LCD in my room, and because I am a perfectionist, I got a power point and a HDMI wall plate installed behind the TV to hide cables. But after it is all set up when I use my PS3 or my PC on the TV through the HDMI cable that I have running through the wall, I am getting pixelation. It is like a lot of dead pixels, but they are always in different spots, so it is more like dead colours. The pixels usually stick to lines of what I’m watching, for example I might watch a movie, and there are dead pixels around a cloud, but when the cloud moves, the pixels follow it. I think the problem might be dues to long length of cables, and multiple joins in the cables. From my PC I have a 1 meter HDMI cable going to the wall plate, which then goes to a 7 meter HDMI cable which goes to the other wall plate which goes to a right angle adapter which goes to another 1 meter cable which goes to another right angle adapter which finally plugs into the TV. Is it a possibility that the long length and lots of connections it is loosing continuity?

Leave a Reply

Login with your Social ID

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Subscribe to Newsletter

Sign Up Today

Get a free copy of Develop Your Own Database Software.
database software, pdf

For A Limited Time